Best Flux for Soldering Electronics

If you work with electronics, you know that soldering is an essential part of your job. However, improper soldering can lead to bad joints or even no joints at all. To help increase the likelihood of a good solder, professionals recommend the use of a flux.

What is Flux in Soldering?

When solder is melted down to form a joint between two opposing metal surfaces, it crease what is referred to as a metallurgical bond. In other words, the solder chemically reacts with other metal surfaces to create a joint. For a solid bond, there are two main things you need. The first is a solder that is compatible, in a metallurgical sense, with the types of metals you are bonding. Secondly, the metal surfaces that are to be jointed should be free of oxides, dust, and other such particles that can damage the integrity of the solder joint. While cleaning metal surfaces can easily remove the dust and grime, oxides are a different story.


When a metal surface comes into contact with oxygen, it creates a chemical reaction. This reaction creates metal oxides on the surface of your material and can impact conductivity, current flow, and your solder. Rust on iron, for example, is a visible iron oxide created by this process. Tin, aluminum, copper and almost all other metal surfaces are susceptible to oxidation. When you metals are coated in oxides, soldering can become difficult, if not impossible. We live in a world supported by oxygen, so you will never be able to have a metal surface completely devoid of all oxides. When you solder, you apply high heat to the area. Oxidation occurs much faster when this type of heat is applied. By using flux, however, on the metal surface, you can prevent the growth of additional oxides while applying heat to your solder joint.

What Flux Does

The flux you choose is a chemical component that is vital to a successful solder. Flux should provide three key things. First, it should chemically clean your metal surfaces, help with the flow-ability of your filler materials over the base metals, and provide a protective barrier between the metal and your soldering heat. Second, flux should assist with the heat transfer between the metal surface and your soldering heat source. Third, your flux should help to reduce and remove any surface metal oxides currently sitting on your metal surfaces.

Types of Flux for Soldering

In certain cases, the flux that is typically included within the core of a solder wire is good enough. However, there are certain situations where the use of an additional flux is beneficial. This includes things like surface mount soldering as well as de-soldering. Regardless of the reason you are using a flux, the most ideal product is the one that is the least acidic but still works on any oxidation on the surface of your component. With that, it is important to point out that there are different types of flux to choose from.

Rosin Flux

One of the oldest types of flux is based off of rosin. (Rosin is a refined and purified pine sap.) While rosin flux still exists today, it contains a blend of fluxes instead of just pure pine sap. This helps to optimize the flux and increase its performance and characteristics. One of the great features of a rosin flux is that it potent and acidic only when in its liquid (hot) state. When it cools, however, it becomes solid and inert. Because it becomes inert when cold, rosin flux can be left in place when your soldering is complete. (That is unless the printed circuit board (PCB) or other surface heats to the point of melting the resin flax while in use. Should this occur, the resin can actually begin to eat away at the connection.) While a resin flux does become inert, it is always recommended that you remove it once your solder is done anyway. Rosin flux can be easily removed with alcohol.

Organic Acid Flux

Organic acid (OA) flux is extremely popular. OA flux is actually a water soluble flux. OA fluxes use common, but weak, acids. This includes things like citric, lactic, or stearic acids. These weak acids are then combined with other solvents, such as isopropyl alcohol or water. The phrase ?weak acids? may make these fluxes seem weaker than other types. However, OA fluxes are stronger than resin versions. The acids in an OA flux work to clean oxides from metal surfaces much more quickly. Because these fluxes are water soluble, they are easier to clean up and remove. In fact, they can be removed with just water. Unlike resin fluxes, which become inert and could potentially be left on the surface of your PCB, OA products must be removed. (OA flux is electronically conductive and can affect the performance of a PCB if left behind.)

Inorganic Acid Flux

If an OA flux uses ?weak acids?, an inorganic flux uses much stronger ones. Typically, inorganic fluxes will use a blend that includes an acid like hydrochloric acid, zinc chloride, or ammonium chloride. Inorganic must be removed from your metal surfaces after use. Because of the stronger acids, inorganic flux can be extremely corrosive if left behind after use. This can destroy your solder joint. (Inorganic flux should never be used for electronic assemblies or electrical work due to its highly corrosive nature!)

A Note on Solder Fumes

Fluxes contain many chemical compounds. When soldering, the smoke and fumes that are emitted are dangerous. In fact, inhaling soldering fumes has been linked to asthma. Make sure you solder only in a well ventilated area. Additionally, it is important to take proper safety measures to ensure you remove any fumes or chemicals from your skin. This includes wearing a mask, thoroughly washing your hands and face, and avoiding eating or drinking in an area where soldering is performed.

In addition to this, some soldering fluxes will include the phrase ?RoHS compliant.? RoHS is short for ?Restriction of Hazardous Substances.? RoHS, which came from the European Union?s Directive 2002/95/EC, restrict the use of certain materials that have been deemed hazardous when used in and for electrical and electronic products.


The Best Flux for Soldering Electronics

So now, you understand the importance of a flux as well as the different types available on the market. Let?s a take a look at some of the most highly recommended fluxes available on the market today.

MG Chemicals is a well known brand in the electronics world. Their No Clean Flux Paste is a rosin-based paste you apply through the use of a syringe dispenser. (In fact, it comes preloaded in the syringe for easy and precise application.) It provides instant wetting and is compatible with both leaded and lead-free soldering applications as well as with conventional Sn/Pb alloys. Because the MG Chemicals No Clean Flux Paste is rosin-based, any residue that remains after soldering is non-corrosive and non-conductive. Rosin is naturally moisture and fungus resistant as well. MG Chemicals No Clean Flux Paste is RoHS compliant.

  • Pros

Because this is a paste and not a liquid, users have praised it?s sty-in-place application. Once the heat is applied during soldering, however, it quickly melts and spreads where needed. Even though the paste is said to not need cleaning, users recommend you still remove any remaining residue with 99% alcohol as it can be sticky.

  • Cons

While the pre-loaded syringe is a nice feature, some users have noted that the thick flux is very hard to actually dispense. Some reviewers even said they had to use two hands just to depress the plunger! Because of the pressure you have to use to eject the paste from the syringe, some users have stated that they accidently end up squirting out too much. (A work around provided by one user was to actually squirt the paste into a secondary syringe that will allow you more control.)


As the name states, this is a rosin flux paste. It is a thick, honey colored paste that can be applied directly to your soldering site. With a neutral pH of